BentoBox 

By Insertmeow (IMA)

Non-Printed Parts List
----------------------------
Part numbers for Mcmaster-Carr are provided but many can be substituted with local hardware store parts if the specs are similar enough
----------------------------
OEM Ruger 10/22 Parts:
CH- Charging Handle Assembly
BA- Bolt Assembly
TDP- Takedown pins and bolt stop pin
TP- Trigger Pack

Choice of Barrel Bushing Insert: (Pick One)
I1- Heat Insert- McMC#3378A142 (Drill Bushing for Plastic, 0.5" ID, 3/4" OD, 3/4" Long)
I2- Bronze bearing- McMC#9440T37 (Flanged Bronze Bearing 1/2" Shaft, 5/8" Housing ID, 3/4" Long)
I3- Drill Shaft bushing- McMC#8492A284 (Press-Fit Drill Bushing with Head, 0.5" ID, 3/4" OD, 3/4" Long)

Hardware:  (all #12 screws can be substituted with 1" long versions or replaced with heat inserts and smaller OD screws [eg: M4 screws and heat inserts])
F1- 2x #12-24 Socket Head Screw 1-1/2" Long - McMC#91864A051 (can be substituted with #12-24 1" long Gun Screw available at some hardware stores)
F2- 1x #12-24 Socket Head Screw 1" Long  - McMC#91251A454 (can be substituted with #12-24 1" long Gun Screw available at some hardware stores)
F3- 1x #12-24 Socket Head Screw 7/8" Long - McMC#91251A461 (can be substituted with #12-24 1" long Gun Screw available at some hardware stores)
N1- 1-2x #8-32 Nut - McMC#90480A009 (can use any #8-32 nut as long as it fits into the inlay)
S1- 1x 1" Long, 0.3" OD, 0.236" ID Compression Spring - McMC#9434K59

Misc Parts:
BRL- 22LR Barrel Liner (currently speced for Redmans 22LR liner from Brownells, other 22LR liner could be used but may require an ID change to the printed barrel)

Optional Parts:
F4*- 2x #8-32 Socket Head Screw 1/4" Long - McMC#91251A190 (only used when affixing a printed takedown latch to an OEM barrel)

Folding Grip Chassis additional hardware:
P1- 1x M5x12mm (or M5x15mm) Hex Set Screw (or roll pin, or rod, as the hinge pin)
M1- 1x 6mm x 6mm Cylinder Neodymium Magnet (or 1/4"x1/4" Cylinder neodymium magnet - https://www.apexmagnets.com/magnets/1-4-x-1-4-cylinder-neodymium-magnet)

Stock/Brace Hardware:
P2- 1x 4mm OD Rod 54mm long (can be substituted with similar imperial sized rod or pin)
P3- 1x 3mm OD Rod 30mm long (can be substituted with similar imperial sized rod or pin)
M1- 1x 6mm x 6mm Cylinder Neodymium Magnet (or 1/4"x1/4" Cylinder neodymium magnet - https://www.apexmagnets.com/magnets/1-4-x-1-4-cylinder-neodymium-magnet)
F5- 1x 1/4"-20 Hex Head Screw 1-1/4" Long - McMC#92979A126
N2- 1x 1/4"-20 Locknut (Nylock) - McMC#95615A120
S2- 1x Compression Spring, 0.75" Long, 0.3" OD, 0.218" ID - McMC#9657K287

